COMPACT SWEEPER SWINGO 200+ PUSHED 2-BRUSH SYSTEM

Chippenham Town Council invites companies to supply competitive quotes for the supply of the following: A COMPACT SWEEPER SWINGO 200+ PUSHED 2-BRUSH SYSTEM Specification Engine Euro6 - Common Rail 4 cylinder, displacement 2960 to 3000 cm³ 60 kW to 65 kW @ 2300 to 2500 rpm Max. torque 270 Nm @ 1350 rpm Transmission Full hydrostatic transmission with 2 drive modes (sweeping + transit) via rear axle with differential Stepless and automatic load-dependent transmission control (automotive drive) Axles Hydraulic power steering Selectable 4-wheel steering Tyres 225/70 R15 to 225/80 R15 Mechanical/Coil spring suspension for front and rear axle inc damper and front anti-roll bar Cab Cabin with two seats mounted on elastic rubber elements for low vibrations Ergonomic high back driver's seat with mechanical or air stepless suspension adjustment, fully adjustable Driver and passenger side sliding windows Heater / ventilation with recirculating and fresh air with adjustable vents. Minimum of 10 vents, 6 adjustable Air conditioning Height and inclination adjustable steering column One key operating fuel cap, doors and ignition. Minimum of 3 keys supplied per vehicle Central Colour display with information on all relevant vehicle data and board computer, incl. on board diagnostics Control of the sweeping systems via an ergonomic door control panel with joysticks Cruise control function Cab floor windows for optimum view on brushes and suction nozzle Water System Fresh water tank: 175l to 190l Re-circulating water tank: 175l to 190l plus Re-circulating water up to 250l in hopper Total Re-circulation water 350l to 440l Total water capacity 500l to 630l Re-circulating water discharge via in cab control Water tank made of impact resistance polymer 2 water nozzles per brush- adjustable directly on the brushes Brush System Heavy duty pushed 2-brush-system Brush diameter 800mm to 900mm Hydraulic ground pressure adjustment Brush speed individually adjustable 0 - 130 max rpm Brush material either Plastic (Poly), mixed (steel-Poly) or steel Suction Hot galvanized steel suction box for enhanced corrosion protection and strength Guided on swivelling castor wheels Hydraulic activated debris flap Hydraulic lifting including incremental lifting to nozzle box Pulled nozzle box system to ensure increased damage protection LED work light to illuminate the work area around the suction nozzle box Hopper Drilled Hopper Screen not wired Aluminium corrosion resistant construction 1.9 to 2.1m³ gross volume Suction tube in the hopper made of stainless steel Dirt water separation screens made of stainless steel, mounted to front and side walls in the hopper Hopper lid hydraulic operated, can be opened separately Hopper functions can be controlled in cab or via external control pendant Hydraulic tipping to the rear - 1.400mm to 1.550mm Manually operated hopper raise feature in case of engine breakdown/ loss of power Hydraulic system Load-Sensing hydraulic system Hydraulic tank made of impact resistance polymer Hydraulic filter blockage and hydraulic oil low level and hydraulic temp. warning system Hydraulic steel pipes with factory fitted protected against corrosion Brake System Hydraulic servo assisted brake system on all 4 wheels Dual circuit brake system (acting on front and rear axle) Disc brakes on front and rear axle Electro hydraulically operated parking brake with hill hold assist Electric System 12 Volt battery with 90 to 100 Ah Alternator 12V greater than 130A Lighting according to EC regulations Beacon foldable with protection bracket Dimensions Height with beacon 2.350mm max Height without beacon 1.900 mm to 1.990 mm Wheelbase up 1.810mm to 1.910mm Length with brushes up to 4.600 mm Width without brushes up to 1.315 mm Steering / turning Circle 4-wheel steering switchable in cab Turning cycle Kerb to Kerb up to 4.750 mm Weights Payload between 1.750kg and 2,100kg Gross vehicle weight up to 5,000kg Other items Hopper painted in white with chapter 8 markings DAB + Radio with USB connection and Bluetooth hands-free module Reversing signal disengage able Rear view and suction nozzle camera Between 140 bar to 150 bar high pressure washer in frame with 8m to 10m hose recoil drum and 900m Hand Lance. Additional Requirements Rear mounted wonder hose Near side weed control system incorporating reinforced brush arm, rated lift arm, heavy duty brush, Motor and weed ripping brush, independent brush lift control and brush head articulation controlled From cab Training Train the operator training for 2 operatives The Council would be interested in receiving quotations to outright purchase the above vehicle. For further details interested parties should contact either: Wayne Lewkowicz Environmental Services Supervisor (Streetscene) 07875 665502 [email protected] Or Will Tidmarsh Head of Environmental Services 07875664690 Email: [email protected] Chippenham Town Council Town Hall High Street Chippenham Wiltshire SN15 3ER Tel: 01249: 446699 Email: [email protected] Terms and Conditions: i) All prices tendered are to be net of VAT which are to be added by the successful tenderer at invoice stage. ii) A Chippenham Town Council Purchase Order will be issued to the successful tenderer as confirmation of the works. iii) The successful Tender will be paid in full in the 2026/27 financial year. iv) Reservation: The Town Council reserves the right to not accept the lowest, or any Tender. Tenders must be provided on the attached form and returned either: In an envelope addressed to - Chippenham Town Council CEO, Town Hall, High Street, Chippenham, Wiltshire, SN153ER, and Marked COMPACT SWEEPER SWINGO 200+ PUSHED 2-BRUSH SYSTEM or via email to [email protected]. Failure to do this will lead to disqualification from the quotation process. TENDER FORMS MUST BE RETURNED BY: 09 March 2026.